cnc laser cutter plastic acrylic wood laser engraver 1410

Description

As for competitive prices, we believe that you will be searching far and wide for anything that can beat us. We can state with absolute certainty that for such quality at such prices we are the lowest around for co2 laser tube,co2 laser tube 200w,co2 laser tube 40w,Please send us your specifications and requirements, or feel free to contact us with any questions or inquiries that you may have.

---

cnc laser cutter plastic acrylic wood laser engraver 1410

MODEL	POWER	OUTER DIAMETER	Operating current	LENGTH	CATALYST	WARRANTY
RCS80	80	Φ80±2	20	1250	YES	6 MONTH
RCS100	100	Φ80±2	23	1450	YES	6 MONTH
RCS130	130	Φ80±2	25	1650	YES	6 MONTH
RCS150	150	Φ80±2	28	1850	YES	6 MONTH

1.Installation Requirement

Please read the operation instruction before you start installation.

2.The dedicated power DY13 should be equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 24kv).

2.1. It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will

be punctured by electricity and may cause water leakage.

2.2.Operation conditions

Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10℃-40℃The operating environment: temperature 2-40℃; humidity 10-60%The working current: test current is 30mA. Maximum working current is 30mA. The running current

must be kept below 28mA. The life span can reach 10,000 hours if the current is kept below 26mA.

The ammeter must be connected to the negative electrode of laser tube. When it is working under over-high current for long term, the negative pole will appear brown yellow, and the life span will be shorten rapidly. To protect dust from going into the insulation sheath, please wrap it with plastic film.

3. Working Performance

Cutting function. Engraving function: Very good. When the working current is 4mA and the tube is in the

state of preionization, the laser can be used for high-frequency impulse engraving.

4. Key Notes

Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:

1) When the mirror is polluted, do not turn on the laser.

2) Blow the mirror surface sideways with an air blower.

3) Spray the pure alcohol on the mirror surface with sprayer.

4) Turn on the laser after the alcohol gets fully volatilized.

5) If the methods above don’t work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.

Attention: it is forbidden to clean the mirror with acetone.

The screws in the front and back ends of the laser tube are not allowed to be moved, otherwise the out power will be declined,  moreover the tube will be scrapped.

Put the acryl 300mm far away from output mirror, when testing its laser spot.

5. Safety

The laser beam is invisible light. Please wear protective glasses when debugging the laser.

The positive pole is in high voltage. Pay attention to the security marks.

6. Storage and Transportation Requirement

Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40℃, and the requested humidity is 10-60%. Pack the laser as in the original way. Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from vertically sliding during transportation.

The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider.
Our eternal pursuits are the attitude of ,regard the market, regard the custom, regard the science, and the theory of ,quality the basic, trust the first and management the advanced, for cnc laser cutter plastic acrylic wood laser engraver 1410, we are now looking forward to even greater cooperation with overseas customers based on mutual benefits. If you are interested in any of our products, please feel free to contact us for more details.